Warning: file_get_contents(/home/content/62/10983362/html/timer-relay/wp-content/plugins/amzn/templates/kefuang/inlinesingle.html) [function.file-get-contents]: failed to open stream: No such file or directory in /home/content/62/10983362/html/timer-relay/wp-content/plugins/amzn/amzntemplates.php on line 29
Warning: file_get_contents(/home/content/62/10983362/html/timer-relay/wp-content/plugins/amzn/templates/kefuang/inlinemulti.html) [function.file-get-contents]: failed to open stream: No such file or directory in /home/content/62/10983362/html/timer-relay/wp-content/plugins/amzn/amzntemplates.php on line 29
Are you trying to find critiques about dc relay coil, study the product reviews, we are going to tackle the various elements, fundamentals as well as other points of interest about dc relay coil. Many readers discover that this weblog is a superb place to start if you want to buy the prodct about dc relay coil.
We will deliver detailed resources like reviews, images, articles, videos and hyperlinks that may possibly be of good use for all those who need to make a much more detailed study about it.” for those who want to get far more specifics about dc relay coil. just see clearly as under.
If you would prefer to suggest associated points about %keywords% that could be featured in this blog, you could get in touch with us and we will happily seem into it. Feel no cost to let us know, as we would like to generate our site the top resource web-site for our readers who are serious about %keywords%. We would like to know your thoughts along with other feedback to produce our weblog enhanced. Please feel free to leave a comment or perhaps a message. We would really like to hear from you.
Russ asked How do i charge my coil gun capacitor?
I have a working coil gun, but i fried the circuit that charges my cap that i took out of a disposable camera. How can i make on of those myself? Does anyone know where i can find schematics on how to build a cap charging circuit that charges up to about 300v using AA or 9v batteries? The simpler the better. In fact, assume i don't know anything about electronics.
And got the following answer:
If you've got enough savvy to whip up a coil gun out of wire, some caps, and a disposable camera, I think you can handle this - a mechanical step-up inverter, no chips and only 4 diodes (or a single fullwave bridge diode pak). Start with a battery holder that can hold at least 6 cells (AA is okay) in series, but start out using only 3 initially, otherwise the voltage might get so high that you blow your caps. Just jumper across the empty battery spots. From Radio Shack, get a 12-volt center-tapped (MUST be center-tapped)transformer and a 5-volt, DPDT (double-pole, double-throw) relay, 1 10-ohm, 10W resistor, and 5 one-amp 1000-volt diodes (something like a 1N4007, I think RS has them). You might also want a pushbutton momentary switch so you can press-to-charge, rather than hooking and unhooking the battery plus lead. And a piece of perfboard big enough for the transformer, battery box and other components is highly suggested. I suggest you create a schematic from the description before you start. We're going to hook the transformer up backwards from it's normal config, applying power to what is usually the secondary (the 12V side), and draw the power from what is normally the primary (the 120V side). The relay has 8 pins total. 2 are for the coil, 3 are the normally-open (NO), normally-closed (NC), and common(COM) of switch A (SWA), and the last 3 are the NO, NC, and COM of switch B(SWB). Start with the batteries removed from the holder and keep them out until finished building. Connect the battery (-) to both the neg. terminal (or either terminal if it isn't polarized) of the relay coil and to the COM pin of switch B of the relay. 1) Connect the (+) battery output to one contact of the momentary switch. 2) Connect the other momentary switch contact to the NC contact of SWA, and to one end of the 10-ohm, 10W resistor. The 10-ohm resistor is to limit charging current to a safe level for the circuitry. 3) Connect the other end of the resistor to the center-tap of the 12V side of the transformer. 4) Connect one of the 12V transformer wires to the NC contact of SWB, and the other 12V transformer wire to the NO contact of SWB. 5) See http://en.wikipedia.org/wiki/Bridge_rectifier if you need to for how to connect 4 of the diodes in a bridge, with the AC ("~") coming from the 120V wires of the transformer. Email me if not clear. 6) Connect the "band" end of the last diode to the relay coil contact that is connected to battery (+), and connect the other end to the other relay coil contact. This is to protect the coil from large inductive spikes that would occur when the relay opens. 7) Now go back to step 1 carefully checking each step for accuracy. Install the batteries. connect your caps to the bridge rectifier output, making sure to hook "+" to "+" and "-" to "-". Do you have a meter? Monitor the DC output voltage of the bridge rectifer (+ and -). Press the momentary switch for just a second while you monitor the meter. The relay should start buzzing and you should get intially a low voltage on the meter, rising fairly rapidly unless you have a really HUGE capacitor arrray. If the voltage tops out too low, add another battery to the battery box and try again. Don't blow your caps, and for God's sake, this is very high energy - be careful, don't let the thought of batteries fool you, this thing can kill a man. SERIOUSLY!!! All standard disclaimers apply, don't electrocute yourself or anyone else, this is NOT a toy!